Mooncell M-TA20 LED synchronous sending card is compatible with VCMA7-V10-out of production. Mooncell M-TA20 has the following features:

1. Two DVI input ports, one for DVI signal main port, the another for backup.
2. Four output ports.
3. Two USB ports, one connects to PC, the other can be cascaded to the same type of receiving card, or other USB devices.
4. Support multi resolution： 1024×768,1280×720,1280×800,1366×768,1600×1200,1920×1080,2048×1152,2560×960 and other frequently used resolutions, as well as resolution back read.
5 .One single Sending card can load 2,350,000 pixels, and one single port can load 650,000 pixels. The graphic position can be setup arbitrarily.
6. Two ways for getting power.
7. It support Chroma restore.

Mooncell TB2000 LED Aviation Plug Transmitter Box Specifications:

1. Product Type: LED display transmitter box, sender box
2. Product Type: TB2000
3. Geared with Aviation plugs
4. Input Voltage: 100V-240V
5. Power Consumption: 15W
6. Box Size: 480MM x 248.8MM x 88MM
7. Application: full-color, single-color

Mooncell M-RA70 LED Panel Mini Receiver Card Features:

1. With 32 groups of RGB output.
2. A single card with a maximum load of 96K pixels, each data can carry 8K pixels.
3. Wide voltage input, input voltage range is +3.5 V --- +5.5 V.
4. Conventional chip high refresh, high brightness, high gray.
5. Support receiving card parameters back to read.
6. With cable double backup function, support cable detection;
7. Support cabinet temperature, humidity, power supply voltage monitoring, fan control;
8. Support brightness, color point-by-point correction. And does not reduce the receiving area of ​​the receiving card.
9. Support a wide range of driver chips. Support PWM chip, point by point detection chip, conventional chip.
10. Support receiving card pre-screen settings.
11. Support all receiving card parameter monitoring function.
12. Support external environment monitoring function.
13. Intelligent recovery function. There is no need to reload the program after replacing the card.
14. Never black screen. And intelligent power supply, in the event of a power failure, reduce the display brightness.
15. Each interface provides power pins to support the cell board to take power.
16. Meet the EU RoHs standards.
17. Meet the EU CE-EMC standards.

Mooncell M-RC32A RGB LED EMC Receiver Card Features:

1. Conventional RGB output with 24 groups, with 12 HUB75E interface.
2. A single card with a maximum load of 96K pixels, each data can carry 8K pixels.
3. Wide voltage input, the input voltage range of +3.5 V --- +6 V.
4. Conventional chip high refresh, high brightness, high gray.
5. Double backup with network cable.
6. Support brightness and chroma point-by-point correction. And does not reduce the receiving area of the receiving card.
7. Support a wide range of driver chips. Support PWM chip, point by point detection chip, conventional chip.
8. Support receiving card pre-screen settings.
9. Support all receiving card parameter monitoring function.
10. Support external environment monitoring function.
11. Intelligent recovery function. There is no need to reload the program after replacing the receiving card.
12. Never black screen. And intelligent power supply, in the event of a power failure, reduce the display brightness.
13. In line with EU RoHs standards.
14. Conforms to European CE-EMC standard.

MoonCell M-RA30 LED Wall EMC Receiving Card Features：

1. Conventional RGB output with 24 groups, with 12 HUB75 interface.
2. A single card with a maximum load of 96K pixels, each data can carry 8K pixels.
3. Wide voltage input, the input voltage range of +3.5 V --- +6 V.
4. Conventional chip high refresh, high brightness, high gray.
5. Double backup with network cable.
6. Support brightness and chroma point-by-point correction. And does not reduce the receiving area of the receiving card.
7. Support a wide range of driver chips. Support PWM chip, point by point detection chip, conventional chip.
8. Support receiving card pre-screen settings.
9. Support all receiving card parameter monitoring function.
10. Support external environment monitoring function.
11. Intelligent recovery function. There is no need to reload the program after replacing the receiving card.
12. Never black screen. And intelligent power supply, in the event of a power failure, reduce the display brightness.
13. In line with EU RoHs standards.
14. Conforms to European CE-EMC standard.

Mooncell VCMA7-V30 is a Synchronized full color LED display sending card that specially designed by Mooncell with the following features:

1. It comes with One DVI Input.
2. Dual Network Interface
3. With USB Interface, Multiple Sending Cards Could be Connected to the same computer(Cascading)
4. Supporting Multiple Resolutions: 640X480、800X600、1024X768、1280X1024、1280X720、1280X800、1366X768、1600X1200、1920X1080、2048X1152、2560X960，and it can read-back (detect) the computer’s screen resolution.
5. The Number of Pixels it could upload: One Single Card can load 1300 thousand Pixel and One Single Network Interface can load 650 thousand Pixel and the Image Window is movable.
6. 3 Ways to take the power (get your cards powered on (electricity)).
7. It supports “Color Space Conversion”.

Mooncell VCMA10-V11 Big LED Wall Sending Card Features:

1. It comes with 2 ways of DVI Inputs, the spare one will be used as the backup.
2. 4 Network Ports for Outputs.
3. With USB Interface, Multiple Sending Cards Could be Connected to the same computer(Cascading)
4. Supporting Multiple Resolutions: 1024X768、1280X800、1366X768、1600X1200、1920X1080、2048X1152、2560X960，and it can read-back (detect) the computer’s screen resolution.
5. The Number of Pixels it could upload: One Card can load up to 2.6 million Pixels and One Single Network Interface can load up to 650 thousand Pixels and the Image Window is movable.
6. 2 Ways to take the power (get your cards powered on (electricity)).
7. It supports “Color Space Conversion”.

Monncell PC10 LED Power Supply Control Card Details:

Product Type: Power Supply Control Card
Product Model: Mooncell PC10
Input Voltage : +3.5V---6V
Output Power: 7.5W
Product Dimensions: 144mm X 92mm
Supported Display Module: Single Color, Dual Color, Full Color

Mooncell VCSG3-V51 LED Board Receiving Card Features:

1. 60 ways of outputs in serial with one card, which can be extended to 120 ways.
2. The maximum output of the RGB are 21 sets
3. The maximum pixel that one could load is 64K, each set of the data could load 8k pixel.
4. Input voltage: 3.5V--6V
5. High Refresh rate, high brightness and high gray grade with common IC (Driver).
6. Dual backup for the network Cable
7. To get the single pixel calibration without decreasing the pixel load area
8. Variety of Drivers are supported. It supports PWM IC, Point by point Detecting IC and Conventional IC.
9. It supports to save the settings beforehand.
10. It supports to monitor all the parameters of the receiving card.
11. It supports to monitor the environment.
12. Intelligent recovery function, swapping the receiving cards without the need of loading all the data again.
13. Companied with Mooncell Intelligent Power Supply ( two power supplies as in parallel, equalized current, short-circuit protection) you will never ever get black screen.
14. It confirms to RoHs and CE-EMC standards.

Mooncell VCSG3-V52A LED Panel Receiving Card Features:

1. 60 ways of outputs in serial with one card, which can be extended to 120 ways.
2. The maximum output of the RGB are 21 sets
3. The maximum pixel that one could load is 64K, each set of the data could load 8k pixel.
4. Input voltage: 3.5V--6V
5. High Refresh rate, high brightness and high gray grade with common IC (Driver).
6. Dual backup for the network Cable
7. To get the single pixel calibration without decreasing the pixel load area
8. Variety of Drivers are supported. It supports PWM IC, Point by point Detecting IC and Conventional IC.
9. It supports to save the settings beforehand.
10. It supports to monitor all the parameters of the receiving card.
11. It supports to monitor the environment.
12. Intelligent recovery function, swapping the receiving cards without the need of loading all the data again.
13. Companied with Mooncell Intelligent Power Supply ( two power supplies as in parallel, equalized current, short-circuit protection) you will never ever get black screen.
14. It confirms to RoHs and CE-EMC standards.

Mooncell EM10 LED Multifunction Control Card Details:

Product Type: Control Card for Temperature,Humidity and Lightness
Product Model: Mooncell EM10
Input Voltage: +3.5V---6V
Output Power: 7.5W
Product Dimensions: 144mm X 92mm
Supported Display Modules: Single Color, Dual Color, Full Color

Mooncell VCSG3-V23C LED HUB75 Receiving Card Features:

1. It conventionally has 16 sets of RGB Output, and features 8 hub75 interfaces.
2. The maximum pixel that one card could load is 64K, each set of the data could load 8k pixel.
3. Input voltage: 3.5V--6V
4. High Refresh rate, high brightness and high gray grade with common IC (Driver).
5. Dual backup for the network Cable
6. To get the single pixel calibration without decreasing the pixel load area
7. Variety of Drivers are supported. It supports PWM IC, Point by point Detecting IC and Conventional IC.
8. It supports to save the settings beforehand.
9. It supports to monitor all the parameters of the receiving card.
10. It supports to monitor the environment.
11. Intelligent recovery function, swapping the receiving cards without the need of loading all the data again.
12. Companied with Mooncell Intelligent Power Supply you will never ever get the black screen.
13. It conforms to RoHs and CE-EMC standards.

Mooncell VCSG3-V23D-EX LED Receiving Card is specifically designed for LED displays with Irregular Shapes with the following features:

1. The maximum output of the RGB is 21 sets
2. The maximum 96k pixel could be loaded, each set of the data could
loads 8k pixel.
3. Input voltage: 3.5V--6V
4. High Refresh rate, high brightness and high gray grade with common
IC (Driver).
5. Dual backup for the network Cable
6. It supports to save the settings beforehand.
7. It supports to monitor all the parameters of the receiving card.
8. It supports to monitor the environment.
9. Intelligent recovery function, swapping the receiving cards without the
need of loading all the data again.
10. Supporting LED Displays with Irregular Shapes
11. It conforms to the RoHs and CE-EMC Standards.

Mooncell VCSG3-V22D LED Screen Receiving Card Features:

1. It conventionally has 16 sets of RGB Output, which can be extended to 32 Sets.
2. The maximum output of the RGB is 21 sets
3. One single card Connection in series can get 64sets of RGB output, which can be extended to 128
4. The maximum pixel that one can could load is 64K, each set of the data could load 8k pixel.
5. Input voltage: 3.5V--6V
6. High Refresh rate, high brightness and high gray grade with common IC(Driver).
7. Dual backup for the network Cable
8. To get the single pixel calibration without decreasing the pixel load area
9. Variety of Drivers are supported. It supports PWM IC, Point by point Detecting IC and Conventional IC.
10. It supports to save the settings before hand.
11. It supports to monitor all the parameters of the receiving card.
12. It supports to monitor the environment.
13. Intelligent recovery function, swapping the receiving cards without the need of loading all the data again.
14. Companied with Mooncell Intelligent Power Supply( two power supplies as in parallel, equalized current, short-circuit protection) you will never ever get black screen.

Mooncell VCSG3-V23D-A LED Sign Receiving Card Features:

1. It conventionally has 16 sets of RGB Output, which can be extended to 32 Sets.
2. The maximum output of the RGB is 21 sets
3. One single card Connection in series can get 64sets of RGB output, which can be extended to 128
4. The maximum pixel that one can could load is 64K, each set of the data could load 8k pixel.
5. Input voltage: 3.5V--6V
6. High Refresh rate, high brightness and high gray grade with common IC (Driver).
7. Dual backup for the network Cable
8. To get the single pixel calibration without decreasing the pixel load area
9. Variety of Drivers are supported. It supports PWM IC, Point by point Detecting IC and Conventional IC.
10. It supports to save the settings beforehand.
11. It supports to monitor all the parameters of the receiving card.
12. It supports to monitor the environment.
13. Intelligent recovery function, swapping the receiving cards without the need of loading all the data again.
14. Companied with Mooncell Intelligent Power Supply (two power supplies as in parallel connection, Sharing current, short-circuit protection) you will never ever get black screen.
15. It conforms to the RoHs and CE-EMC Standards.

Mooncell M-RA50 LED Wall Thin Receiver Card Features:

1. RGB Outputs: 28/24 Sets.
2. The maximum pixel that one card could load is 96K, each set of the data could load 8k pixel.
3. Input voltage: 3.5V--6V
4. High Refresh rate, high brightness and high gray grade with common IC (Driver).
5. Dual backup for the network Cable
6. To get the single pixel calibration without decreasing the pixel load area
7. Varieties of Drivers are supported. It supports PWM IC, Point by point Detecting IC and Conventional IC.
8. It supports to save the settings beforehand.
9. It supports to monitor all the parameters of the receiving card.
10. It supports to monitor the environment.
11. Intelligent recovery function, swapping the receiving cards without the need of loading all the data again.
12. Companied with Mooncell Intelligent Power Supply you will never ever get the black screen.
13. It conforms to RoHs and CE-EMC standards.